Shower Walls in Meridian, Idaho
Cement board and membrane, acrylic panels, or solid surface. The waterproofing behind the finish is the spec.
Free estimate.
- Free estimates
- Treasure Valley
- Local crew
- One number
This job covers
- Cement-board and membrane walls
- Acrylic wall panels on a rigid backer
- Solid-surface wall sheets
- Valve wall only, corners still tight
Shower Walls in Meridian, Idaho
Meridian Quality Shower Conversions handles shower walls in Meridian when the finish in the stall has failed and the pan may still be sound. Cement board, membrane, then the finish. The rest of the house is not this job.
Call (208) 274-7129 with photos of the three walls and whether the pan moves. We quote the wet walls.
Shower Walls We Rebuild in Meridian Stalls
Walls are the spray plane. Cement-board and membrane, acrylic sheets, solid-surface panels, and a valve-wall-only opening each change how far we strip.
Cement-board and membrane walls
The production repair. Gypsum in the spray comes out. Cement board goes on the studs. Sheet or liquid membrane to the pan flange. Tile or another finish sits on that. This is the spec, not a paint.
Acrylic wall panels on a rigid backer
Three sheets, factory corners, a matching pan when we can. Fasteners into studs. Expansion gaps at the heat of a west bath. Not a liner left on the old tub.
Solid-surface wall sheets
Fewer seams, heavier sheets, still a flat wall underneath. Seams follow the maker. This finish still dies into a pan, not into carpet.
Valve wall only, corners still tight
A leak at the mixing valve can be a one-wall open. Blocking, a new membrane patch that laps the old, and trim. If the corner paper is stained, it is not a one-wall job.
How We Handle Shower Wall Installation in Meridian
- We probe the flange and the corners. Soft board is marked for cut-out.
- Finish comes off. Backer goes to the studs where it failed.
- Membrane laps the pan flange. Inside corners tooled. Valve hole detailed.
- Finish: panels or tile. Silicone at the change of plane. Use waits on the cure.
Materials and Methods
Walls fail when gypsum takes the spray. Cement board or foam backer. ANSI A118.10 membrane, sheet or liquid. Fasteners in the field per the board maker, then covered by membrane. Mixing valve penetration sealed. International Plumbing Code does not pick your tile, but the wet wall still has to keep water off the plates. Silicone at corners and at the curb. We do not set tile on paper gypsum. We do not treat grout as waterproofing.
What Shower Wall Installation Costs in Meridian
Angi publishes shower tile from about $1,800 to $6,850 by type. HomeAdvisor lists acrylic around $500 to $2,500 and fiberglass higher in some bands. Prefab inserts on Angi sit near $500 to $2,000. Three movers: how much gypsum is rotten, panels versus tile, and whether the pan flange can stay. We quote the walls we open.
Cement board behind production vinyl surrounds
Builder kits in 2000s Meridian baths often sit on gypsum. The kit hides it. The flange stains. We cut to the studs and put cement board and a membrane in. The new finish is the easy part.
A west-facing bath along Eagle Road or Fairview cooks the corner joints. Expansion in acrylic, and a membrane under tile, both need that heat named on the visit.
Call (208) 274-7129 with wall photos and a note if the pan already flexes.
Paper-faced gypsum in the spray is the failure we cut out of 2000s kits. Cement board and a membrane go back. A west bath cooks corner joints in July. Expansion gaps on acrylic and silicone on tile both need that heat named. We do not caulk a kit to bare drywall and leave.
Questions
How do I get a shower wall installation estimate in Meridian?
Send photos of the three walls, the city, and whether the pan is staying. We quote the wet walls of the stall, not a kitchen backsplash and not the rest of the bath. Soft board behind a kit changes the bid because that gypsum comes out to the studs.
Is greenboard enough in a shower?
No. Moisture-resistant gypsum is for rooms, not for the spray. Cement board or a foam wet-area board is the backer. A membrane still goes on that board. Paper-faced gypsum in the stall is the rot we cut out of production kits.
Do the walls come off if the pan stays?
They can, if the pan flange can take a new membrane tie. Some kits share a joint you cannot open without wrecking the base. We look at that joint before we bid walls-only. A walls-only bid on a cracked pan is a stall that still leaks.
Acrylic panels or tile on the walls?
Both are wall finishes. Acrylic is faster and a system with a matching pan. Tile needs a membrane and dry time. Neither finish is the waterproofing. Say which look you want. We still open the flange either way. Grout is not a membrane.
Can you replace one wall only?
A valve wall with a leak can be opened without stripping all three if the corners are still tight. Inside corners are the weak joint. If two walls share a failed corner, both come off. We do not patch a corner with caulk and call the wall done.
What do guides say shower walls cost?
Angi lists shower tile around $1,800 to $6,850 depending on type, and surround materials in prefab tables from a few hundred dollars up. HomeAdvisor acrylic bands sit near $500 to $2,500. Backer and membrane sit under those finishes. We quote the three walls.
Ready for a shower conversion estimate in Meridian?
Tub out, shower in. Tile or acrylic. Free estimate, no obligation.